OVEN INSTALLATION MANUAL

ENGLISH

 

 

1

 

TABLE OF CONTENTS

 

page 

 

page 

 

page 

 

1

 

n

o

i

t

c

u

d

o

r

t

n

I

Installation notes

 

2 Connecting 

to 

120/208V circuit

Tools you will need

 

1        Wall or under counter installation, single oven              3         Electrical connections

 

Power requirements

 

1        Wall installation double oven                                               3        3-wire branch circuit

 

Choosing oven location

 

t

i

u

c

r

i

c

 

h

c

n

a

r

b

 

e

r

i

w

-

4

 

4

 

n

o

i

t

a

l

l

a

t

s

n

i

 

h

s

u

l

F

 

1

 

Steps for installation

 

1 Electrical 

supply

 

Final check list

 

Technical data 

 

2 Wiring 

requirement

 

 

 

 

 

 WARNING 

If the information in this manual is not followed exactly, 

a fire or explosion may result causing property damage, 

personal injury or death. 

 

 
 

INTRODUCTION 

Please read these instructions 

COMPLETELY AND

 

CAREFULLY

. They will save you time and effort and help to 

ensure optimum oven performance. 
Be sure to observe all WARNINGS. These installation 
instructions are intended for use by a qualified installer. 
In addition to these instructions, the oven shall be installed: 

In the United States, in accordance with the National 
Electric Code/State and Municipal codes and/or local 
codes. 
In Canada, in accordance wi

th Canadian Electric  

Code C22.1-latest edition/Pro vincial and Municipal 
codes and/ or local codes. 

These shall be carefully followed at all times. 
NOTE: IF INSTALLING YOUR OVEN IN 
           CANADA PLEASE CHECK TO MAKE 
           SURE THAT YOU HAVE A MODEL 
           WITH THE US AND CANADIAN LISTING 

 

MARK, AS SHOWN ABOVE: 
Mark as shown above means the oven complies with both  
US and CANADIAN Standards.  

 

TOOLS YOU WILL NEED 

The following tools are needed to install your new oven: 

Tape measure and straightedge or ruler 
Pencil 
Phillips screwdriver 
Level 
Wire cutters and wire stripper 
Hand or saber saw 
1” (2,5cm) Hole saw 
Drill and drill bit 
Safety gloves and goggles 
Volt meter (0-250VAC) 

PACKAGING 
Remove all tape and packaging before using the oven. 
Destroy the packaging after unpacking the oven following  
the rules in force in your  town. Never allow children to play 
with packaging material. 

POWER REQUIREMENTS 

The oven must be supplied with the proper voltage and 
frequency. The oven is manufactured to be connected to a 
three-wire or four-wire, single phase, 120/240 Volt, 60 Hz AC 
electrical supply on a sepa rate circuit fused on both sides of 
the line. If a 120/208 Volt circuit must be used, see Connecting to 
120/208 Volt Circuit, in this manual. A circuit breaker or time delay 
fuse, sized not to exceed the circuit rating of the appliance 
specified on the rating plate located on the frame behind the 
door of the oven is recommended (see figure at page 5). 

It is recommended that you have the electrical wiring and 
hook-up of your oven performed by a qualified electrician. 
After installation is complete have the electrician show you 
where the main disconnect is and which of the circuit 
breakers/fuses are for the oven. 

 

CHOOSING OVEN LOCATION 

Carefully select the location where the oven will be placed. 
The oven should be located for convenient use in the 
kitchen, but away from strong drafts.  
Strong drafts may be caused by open doors or windows, or by 
heating and/or air conditioning vents or fans. Make sure that 
electrical power can be provided to the location selected. 

 

STEPS FOR INSTALLATION 

The following pages provide the necessary information for 
proper installation of the oven and are arranged as follows: 

Technical Data 
Installation Cutout Dimensions, Required Clearances and 
Mounting instructions for: 
-  Under counter Installation, Single Oven 
-  Wall Installation, Single Oven 
-  Wall Installation, Double Oven 
Electrical Supply and Wiring Requirements, Programming 
required if connecting to 120/208 Volt Circuit. Electrical 
Connections for 3-wire or 4-wire Branch Circuit. 
Final Checklist 

 

The oven must be supplied with copper or alumimum wires.
If aluminum wire is provided to connect oven to branch 
circuit, UL listed connectors for joining copper and aluminum 
must be used. Follow instructions provided with connectors.

IMPORTANT: Save these instructions for the local electrical inspector use. 

INSTALLER: Please leave this manual with owner for future reference. 

OWNER: Please keep this manual for future reference.