BSH Hausger te GmbH Carl Wery Stra e 34 81739 M nchen GERMANY, siemens home com

BSH Hausgeräte GmbH
Carl-Wery-Straße 34, 81739 München, GERMANY

*9001017650*

      

9001017650 

   941201

siemens-home.com

Document Outline Extractor hood Table of contents en Instructions for installation and use Instruction manual 8 Intended use Intended use ( Important safety information Important safety information : Warning Danger of suffocation! : Warning Danger of death! : Warning Risk of fire! : Warning Risk of burns! : Warning Risk of injury! : Warning Risk of electric shock! Causes of damage Caution! 7 Environmental protection Environmental protection Environmentally-friendly disposal Ç Operating modes Operating modes Exhaust air mode Note: Circulating-air mode Notes 1 Operating the appliance Operating the appliance Note: Control panel model 1 Explanation Setting the fan Intensive setting Fan run-on time Lighting Saturation display Audible signal Control panel model 2 Explanation Setting the fan Intensive setting Automatic mode Sensor control 1. When the fan is switched off, hold the ! symbol for approximately four seconds. The setting is displayed. 2. The sensor control setting can be changed by sliding your finger to the right or to the left across the ||| settings range. 3. To confirm the entry, hold the ! symbol for approximately four seconds. Lighting Saturation display Audible signal 2 Cleaning and maintenance Cleaning and maintenance : Warning Risk of burns! : Warning Risk of electric shock! : Warning Risk of electric shock! : Warning Risk of injury! Cleaning agents Area Cleaning agents Cleaning the metal mesh grease filters : Warning Risk of fire! Notes In the dishwasher: Note: By hand: Note: Removing metal grease filter 1. Open the lock and fold down the metal grease filter. While doing this, place the other hand under the metal grease filter. 2. Take the metal grease filter out of the holder. Notes 3. Clean the metal grease filter. Installing the metal mesh grease filter 1. Insert the metal mesh grease filter. 2. Fold the metal mesh grease filter upwards, locking it in place. 3 Trouble shooting Trouble shooting : Warning Risk of electric shock! Malfunction table Problem Possible cause Solution Replacing bulbs : Warning Risk of electric shock! Replacing halogen bulbs Note: 1. Carefully remove the bulb ring using a suitable tool. 2. Pull out the bulb and replace it with a bulb of the same type. 3. Insert the bulb cover. 4. Insert the mains plug or switch on the fuse again. LED lights : Warning Risk of injury! 4 Customer service Customer service To book an engineer visit and product advice Accessories for circulating-air mode Notes Installation instructions ( Important safety information Important safety information : Warning Risk of death! : Warning Danger of death! : Warning Danger of death! : Warning Risk of fire! : Warning Risk of injury! : Warning Risk of electric shock! : Warning Risk of electric shock! : Warning Danger of suffocation! K General information General information Exhaust air mode : Warning Risk of death! Exhaust duct Note: Checking the wall Electrical connection : Warning Risk of electric shock! : Warning Risk of electric shock! 5 Installation Installation Preparing the installation Caution! 1. Mark a vertical centre line on the wall from the ceiling to the lower edge of the extractor hood. 2. Mark positions for the screws and the contour of the attachment area. 3. Drill five 8 mm diameter holes to a depth of 80 mm for the attachments and press in the wall plugs flush with the wall. Installation 1. Screw on the fixing bracket for the flue duct. ¨ 2. Screw on brackets for the extractor hood hand-tight. Do not firmly tighten the screws. © 3. Screw in the threaded bolt, leaving it protruding out of the wall by 5–9 mm. ª Attaching and aligning the appliance 1. First, remove the protective foil from the back of the appliance and, following installation, remove the foil completely. 2. When attaching the appliance, ensure that it engages firmly with the brackets. « 3. Align the appliance horizontally by turning the brackets. If required, the appliance can be moved to the right or left. ¬ 4. Firmly tighten the screws for the brackets. When doing so, hold the brackets securely in place. ® 5. Firmly tighten the knurled nuts. ¯ Connecting the pipes Note: Exhaust-air pipe Ø 120 mm 1. Attach the reducing connector directly to the air-pipe connector. 2. Attach the exhaust air pipe to the reducing connector. 3. Seal both joints appropriately. Attaching the flue duct : Warning Risk of injury! 1. Separate the flue ducts. 2. Remove the protective foil from both flue ducts. 3. Push one flue duct into the other. Notes 4. Place flue ducts on the appliance. 5. Push the inner flue duct upwards and attach it to the fixing brackets on the left and right. ¨ 6. Press the flue duct downwards until it engages. © 7. Screw the flue duct to the sides of the fixing bracket using two screws. ª